BAUR

PRODUCTS:

Statex® Software

BAUR software for the statistical analysis of the cable lifetime.

BAUR software for the statistical estimation of the cable lifetime engineered by KEPCO.

 

statex®

(developed by KEPCO)

Determine the remaining lifetime of cable routes

All asset managers aim to keep medium-voltage cables in service for as long as possible without jeopardizing the security of supply. BAUR has the solution: The new statex® analysis software evaluates the data from the dissipation factor measurement (tan δ measurement) and uses a patented algorithm to calculate the statistical remaining lifetime of cables – more accurately and clearly than ever before.

  

BAUR software for the statistical analysis of the cable lifetime:

 

statex®

 

 

Cable Testing & Diagnostics:

AC/DC, Portable VLF Testing (with Tan-Delta), Partial Discharge (PD) Spot Tester, Portable PD Tester & Diagnostics, Online PD Spot Tester, PD Pin-pointing, BAUR Software 4™, Statex® Software.

Cable testing and diagnostics

 

To ensure the flow

The BAUR portfolio covers all the important requirements of mains operators with regard to testing and diagnostics technology in the medium-voltage range.

Testing devices are required for the successful commissioning of underground cable networks or repairs. Diagnostic testing devices are used for evaluating the cable status, which enables optimized and anticipatory maintenance planning and thus minimizes failures. This planning is best established with the BAUR diagnostics system.

With truesinus® digital technology, BAUR offers the most modern technology for generating voltage with VLF (Very Low Frequency 0.1 Hz) and thus enables the least destructive testing and diagnostics of modern medium-voltage cables in compliance with the standards.

 

But even for older cable designs, e.g. paper-insulated mass-impregnated cables, BAUR offers ideal devices for DC voltage testing.

  

BAUR products for cable testing and diagnostics:

 

frida | frida TD

liona

PD SGS

PD-TaD 62 | PD-TaD 80

PGK 25

PGK 50 | PGK 80

PGK 70 HB | PGK 70/2.5 HB

PGK 110 HB | PGK 110/5 HB

PGK 150 HB | PGK 150/5 HB

PGK 260 HB

PHG 70 portable | PHG 80 portable

PHG 70 TD | PHG 80 TD

PHG 70 TD PD | PHG 80 TD PD

tracy

viola | viola TD

 

Cable Fault Location:

Burn-down Transformer, Cable Identification, Cable sheath testing & fault location, Pin-pointing, Surge voltage generator, Time-domain reflectometer, Cable route tracing.

Cable fault location

 

The shortcut to the source of a fault

In spite of major developments in this field, faults still occur frequently in cable systems for various reasons. In addition to trained personnel, you also need very efficient equipment to rectify faults.
 

BAUR cable fault location devices and systems cover the entire cable fault location process: During pre-location, the position of the fault is roughly located. The subsequent pinpointing enables the precise determination of the cable fault. You can use various measurement methods depending on the kind of fault and cable type.

  

BAUR products for cable fault location:

 

ATG 2 | ATG 6000

CL 20

IRG 2000 | IRG 4000

KSG 200 

Locator Set/UL 30

protrac®

shirla

SSG 500 | SSG 1100

SSG 1500 | SSG 2100 | SSG 3000

TG 20/50 | TG 600

UL 30

 

 

Cable Test Vans & Systems:

Titron, Transcable, Syscompact.

Cable test vans and systems

 

Equipped to meet all demands.

Precise cable fault location, testing of new and diagnostic testing of existing cable routes – the BAUR cable test vans are suitable for any operation. Fast and reliable. Exactly adapted to individual requirements and predefined vehicle systems.

BAUR conceptualizes its cable test vans with the leading testing systems on the market. A special advantage of our systems is the ability to perform diagnostic testing, fault location and tests simultaneously. You also save on additional, time-consuming tasks.

Our systems can be …

  • operated easily and uniformly in the respective language of the country,
  • installed in any small van up to 3.5 t,
  • upgraded anytime according to your individual requirements.


Our systems are …

  • fully enclosed and thus safe to touch,
  • absolutely reliable due to the redundant system architecture,
  • cost and time-saving in compliance with the standards.

 

Our cable test vans and systems are equipped with the most advanced technology for easy, gentle and highly diagnostic cable testing and diagnostics: truesinus® digital technology from BAUR.

  

BAUR products for Cable Test Vans & Systems:

 

Syscompact 2000

Syscompact 2000 portable

Syscompact 2000 M

Syscompact 4000

BAUR titron

  
Transcable 4000/S 32-3

Transcable 4000/S 70-3
Transcable 4000/A 80-3
Transcable 4000/S 110 -1

 

Insulating Oil Testing:

Breakdown detection, Dissipation factor measurement, Report manager, ITS Lite software.

Insulating oil testing

 

Precise and reliable measurement results

Insulating materials are the elixir of life of electrical equipment. These materials lose their insulating and cooling properties due to impurities and ageing. This damages equipment causes failures and is consequently often accompanied by high costs.


Testing of insulating materials is therefore legally stipulated and regulated by national and international standards. BAUR oil and insulating material testers are characterized by quality levels recognized worldwide that have direct and indirect effects:

  • Precision, reliability and scope of measurement results
  • Reduction of test expenditure and costs
  • A high degree of individualization and user-friendliness
  • Long device service life


This allows us to make complex technologies against the similarly complex background of standards, easy, safe and profitable for the customer.

  

BAUR products for insulating oil testing:

 

DPA 75 C
DTA 100 C
DTA Inline (Discontinued )
DTL C